| |
FREE Network Analyzer Software
 |
There have been free protocol analysers before - but never like this!
This provides full expert protocol analysis of IP and IPX traffic - and is based on the software used throughout the Network Analyser range, complete with the same user interface.
Download FREE Agilent Network Analyzer NOW
|
Read on to understand the full range!
| The Agilent Network Analyzer family represents a new generation
of analyzer designed to meet the challenge of troubleshooting modern
IP-centric and switched networks, building on the award-winning user
interface and expert protocol analysis of the Agilent Advisor range.
Extremely powerful acquisition hardware provides real-time extraction
and re-assembly of packet-based data from within WAN and ATM. And
auto-detection of more than 30 IP encapsulation methods allows expert
higher layer protocol analysis of captured data, in real-time.
A comprehensive range of exchangeable network interface modules,
expert analysis of over 300 protocols, and a choice of portable,
distributed and software versions - the Agilent Network Analyzer
is the troubleshooting tool of choice for modern technologies, including
IP telephony, IP QoS, streaming applications and mobile telephony
applications.
The portable Network Analyzer handles 2 "hot-swappable" Line Interface
Modules (LIM's) for time-correlated measurements
and analysis over a wide range of network interfaces. J6801A and
J6802A Distributed Network Analyzer modules use the same interchangeable
LIM's for for remote and distributed analysis of critical networks.
And a software-only version runs on a standard Windows PC to provide
exactly the same expert analysis for smaller LAN's - or to control
multiple Distributed Network Analyzer modules. |
|
Network Analyzer - Portable
| The J6800A Network Analyzer is a portable
and very rugged "all under one handle" system that includes two
time-synchronized acquisition systems, each supporting any LAN
or WAN/ATM plug-in line interface module (LIM). |
|
Each acquisition system has the following main features:
- Supports any available LAN or WAN/ATM LIM
- LIMs are hot-swappable and interchangeable
- Full-rate capture from any LIM up to 1 Gb/s
- 256 MB capture memory per LIM
- 32 real-time hardware capture filters
- Advanced auto-encapsulation detection (patent
pending)
- Internal time-synchronization between acquisition
systems
- Interfaces for GPS receiver for global time-synchronization
- Agilent Control & Sync technology hardware
provided to allow time-synchronization of attached
Distributed Network Analyzers
|
|
 |
|
In addition, this analyzer includes a full PC running the Microsoft(r)
Windows2000(r) operating system and has the following main features:
- 500 MHz Intel Pentium(c) III processor
- 256 MB processor memory
- 30 GB hard disc drive
- Full keyboard with Touch pad pointing device
- Bright 14" industrial Ultra VGA active display
- CD R/W drive
- Two double-height PC Card slots
- External display and dual USB interfaces (USB optical
mouse supplied)
|
|
The PC is used to control the acquisition systems and to collect (and
post-process) results. The PC is not used for real-time processing
of measurements - this is all done in the acquisition systems and LIMs,
allowing the PC to handle multiple tasks simultaneously without impacting
measurement performance.
back to top
Network Analyzer - Distributed
The Network Analyzer range includes three Distributed Network Analyzer
(DNA) hardware modules, J6801A DNA, J6802A
DNA MX and J6805A DNA ME , and a remote Software Agent, the J6835A, all designed for different
applications across an enterprise network.
All four Distributed Analysis options can be closely integrated with Agilent's Network
Troubleshooting Center (NTC) to provide an enterprise-wide network
monitoring and troubleshooting system. Follow this link for more detail
on Network Troubleshooting Center.
|
J6801A DNA Distributed Network Analyzer
The J6801A is an ultra light-weight module that includes one
time-synchronized acquisition system and Line Interface Module (LIM),
identical to the those of the portable Network Analyser. The
J6801A is controlled by J6840A software running in a local
or remote PC or J6800 portable Network Analyzer.
|
|
The main features are:-
- Remote distributed and dispatch use design
- One acquisition system, identical to the acquisition systems
included in the J6800A
- Controlled via TCP/IP from a standard PC running Network Analyzer
Software, or from a J6800A Network Analyzer, or from Advisor E
series.
- Can be daisy-chained from other Distributed Network Analyzers
- Interfaces for GPS receiver for global time-synchronization
- Agilent Control & Sync technology provided for time-synchronization
with adjacent J6800A or J6801A Network Analyzers
- Same footprint as standard laptop
- Built-in power supply
|
|
J6802A DNA MX Distributed Network Analyzer
The Distributed Network Analyzer MX is a portable or rack mountable
unit that can be left to run unattended in any part of a LAN, WAN
or ATM network. DNA MX includes one time-synchronized acquisition
system and Line Interface Module (LIM), identical
to the those of the portable Network Analyser, supporting the full
range of interface. In addition, the DNA MX includes a controller
running Network Analyzer Software.
|
 |
The main features are:-
- Supports any available LAN or WAN/ATM LIM
- LIM is hot-swappable and interchangeable
- Full-rate capture from any LIM up to 1 Gb/s
- 256 MB capture memory per LIM
- 32 real-time hardware capture filters
- Advanced auto-encapsulation detection (patent pending)
- Interfaces for external GPS receiver for global time-synchronization
- Agilent Control & Sync technology hardware provided to allow time-synchronization
of an attached J6801A Distributed Network Analyze
- Software is supplied for accessing and controlling the J6802A Distributed
Network Analyzer MX from a PC
- Rack-mount kit included
|
J6805A DNA ME Distributed Network Analyzer.
The Distributed Network Analyzer ME is a portable or rack mountable
unit designed specifically for distributed analysis of LAN workgroups.
As with the DNA MX, this unit includes a controller running Network
Analyzer Software and can run unattended. Data capture is via two
half duplex 10/100Base-TX Ethernet (NDIS) interfaces to allow testing
of two half duplex or one full duplex connection.
|
|
The main features are:-
- Two half duplex 10/100Base-TX test interfaces for half or Full duplex
testing
- Local analysis and data storage
- Stand-alone operation
- Software is supplied for accessing and controlling the J6805A Distributed
Network Analyzer ME from a PC
- Rack-mount kit available (J6775A)
|
J6835A Distributed Network Analyzer Software Agent .
The J6835A Software Agent is pure software that can be loaded on to any remote network-connected PC.
Invisible to the local PC user, it allows a remote engineer at a central site to run full expert protocol analysis on the network segment to which the PC is connected. The software can either be permanently installed to give a very cost-effective means of distributed network analysis - or installed on request to investigate particular incidents.
|
|
The main features are:-
- Runs in background on user's PC
- Runs in parallel with user's normal PC use
- Provides local data capture and expert protocol analysis
- Agent is controlled and results are viewed from a remote centralised copy of Network Analyzer software (or hardware)
- Provides the same features and user interface as all other Network Analyzer products
back to top
Network Analyzer - Software
|
J6840A Network Analyzer Software Edition.
J6840A Network Analyzer Software runs under Windows or NT on standard
PC's and provides the same expert analysis and user interface as
the hardware-based Network Analysers using the PC's standard network
interface cards as measurement interfaces for LAN (10/100/1000 Mb/s
Ethernet and Token Ring). For example, the 10/100 PC Cards (PCMCIA
cards) found in most PC laptops can be used as the test interface
for monitoring the LAN network traffic, even while this card is simultaneously
providing the network connection for the PC to that LAN.
|
|
| Network Analyzer Software is remarkably flexible. |
- It provides the consistent base software for controlling hardware-based portable analysers such as the J6800A Network
Analyzer, hardware-based distributed analysers such as the J6801A Distributed Network Analyzer, and the distributed Network Analyzer Software Agent J6835A. The software
is pre-loaded and automatically enabled on the J6800A. A CD and
one license key is supplied with the J6801A to allow the software
to be loaded and enabled on a PC.
- It runs in PCs (and the J6800A) as a software analyzer,
using off-the-shelf network interface cards (NICs) as measurement
interfaces for LAN (10/100/1000 Mb/s Ethernet and Token Ring).
For example, the 10/100 PC Cards (PCMCIA cards) found in
most PC laptops can be used as the test interface for monitoring
the LAN network traffic, even while this card is simultaneously
providing the network connection for the PC to that LAN.
- It provides off-line analysis allowing previously captured
and saved LAN and WAN/ATM data to be re-analyzed using the
full features available on-line for captured data.
|
|
|
Network Analyzer Software is pre-loaded and runs on the embedded PC in the
J6800A Network Analyzer. It is also shipped on CD media with the J6801A Distributed
Network Analyzer, together with a single-use license key to enable the software
on a PC/laptop. License keys plus manuals and CD media for running the software
on additional PCs can be purchased as the J6840A product. For example, a
second engineer can control an existing Distributed Network Analyzer from
his/her PC, with the purchase and installation of the J6841A software product.
The engineer can also use the additional components of the software, Network
Analyzer SW Edition to perform LAN testing with a NIC, and Off-line Analysis
for LAN and WAN/ATM processing. Of course the capabilities of the proprietary
acquisition systems out-perform standard NIC performance, but SW Edition
provides the same useful, extensive measurements.
back to top
J6844A Telephony Network Analyzer
J6844A Telephony Network Analyzer Software is a software solution that works in conjunction with
the J6840A Network Analyzer software to give comprehensive analysis of Voice over IP
applications.
The Agilent Telephony Network Analyzer simplifies and expedites the resolution of quality and signaling problems in IP telephony networks. It provides simple and precise diagnostics of VoIP Quality of Service (QoS) through non-intrusive measurements, including new voice quality measurement technology known as predictive MOS (MOS). It also provides simplified troubleshooting of call signaling and control through embedded expert analysis of VoIP protocols. As an Agilent Network Analyzer solution, the Telephony Network Analyzer includes complete layer 1-7 testing over LAN, WAN, and ATM networks.
Features
- Non-intrusive voice quality measurements using breakthrough Predictive MOS technology
- Simple analysis that exposes the impairments to voice quality
- Precise measurements of IP network performance for VoIP services
- Diagnostics for troubleshooting and identifying problems at the root cause
- Simplified troubleshooting of call signaling and control to quickly turn-up or restore service
back to top
Network Analyzer - LIM's
Fully interchangeable and hot-swappable Line Interface Modules (LIM's)
are common to the portable J6800 Network Analyzer, the Distributed J6801A
DNA and the Distributed J6802A DNA MX. They provide the maximum flexibility,
allowing the same anlyser to swap between any LAN, WAN or ATM interface
without the need to re-boot.
The available list of LIM's includes the following:-
Line Interface Modules (LIMs)
- J6811A STM-1o/OC-3 LIM
- J6812A STM-1e/EC-3 LIM
- J6813A E3/T3 (DS3) LIM·
- J6815A T1/E1 RJ-45/RJ-48C Bantam LIM
- J6816A E1/T1 RJ-45/RJ-48C DB-9 LIM
- J6817A E1 BNC LIM
- J6819A UTP155 LIM
- J6820A V-Series LIM
- J6830A 10 BaseT and 10/100 BaseTX LIM
- J6831A 10/100 BaseFX LIM
- J6832A 1000 BaseX Ethernet LIM
|
|
Main Accessories
- J5491A SX GBIC for J6832A LIM
- J5492A LX GBIC for J6832A LIM
- J5495A Copper GBIC for J6832A LIM
- J6757A Interface Cable sets for J6820A V-Series
LIM
- J6761A Deluxe Carrying Case for the J6800A
- J6762A Transit Case for the J6800A
|
|
back to top
To find out more about the Agilent Network Analyzer family call Phoenix
Datacom on 01296 397711 or use the Request
More Info form.
|
|
